Asbestos was renowned for its insulating, heat-resistant and fire retardant properties. Coupled with it being a relatively affordable material, it is not surprising that asbestos was commonly used within plumbing and heating materials such as boilers, water tanks, calorifiers, pipes, gaskets and valves.
Workers within the plumbing industry have been identified as one of the highest risk groups for being exposed to the fibrous mineral, so arming your workforce with the knowledge of where asbestos can be commonly found in plumbing and heating materials will help to protect them from the health risks associated with exposure to Asbestos Containing Materials (ACMs).
This does not just stop at heating and plumbing materials, either. Asbestos exposure also includes other ACMs in areas that plumbers may be exposed to, such as debris on floors, asbestos insulating board (AIB) walls that pipes may be screwed to and AIB boxing that requires unscrewing to get access to the pipes.
When was asbestos used in plumbing?
In the early 20th century, asbestos was used within pipes and insulation in both domestic and commercial properties to heat water and prevent condensation. Brown asbestos (amosite) was most commonly used within water insulation products due to its high resistance to heat. Furthermore, chrysotile (white) asbestos was used in pipes, gaskets, cement sheets and asbestos cement for its durability.
Present in both residential and commercial properties, asbestos in plumbing can vary significantly in terms of its overall appearance and texture, making it more challenging to identify. In particular, water pipes that are insulated with asbestos are usually covered in a protective coating, which is often painted and therefore even harder to distinguish. There have also been occasions where paint has been found to contain asbestos, too.
Common locations of asbestos in plumbing materials include:
What is the recommended course of action before starting works on asbestos in plumbing?
The duty holder is responsible for managing asbestos risk within the property, and contractors must review the asbestos register before starting their work. As long as asbestos is in good condition and is not disturbed, it will not pose any risk to health. However, exposed asbestos-containing pipes and wraps can easily admit airborne fibres, as can any asbestos that has been left to deteriorate and become friable (is brittle and flakes easily). In the event of discovering or accidentally disturbing asbestos, work should be stopped immediately, the area should be cleared and the issue reported to the relevant individuals as soon as possible.
The duty holder should then organise a qualified surveyor to sample and test the asbestos, as well as providing information on location, amount and the type of ACM/s. If it has been confirmed to contain asbestos, an asbestos management plan should be implemented on the premises locating the presence of ACMs and assess the condition, type and risks.
How are plumbers exposed to asbestos?
According to the HSE, asbestos exposure kills four plumbers every week. Furthermore, the HSE’s Mesothelioma mortality by occupation statistics in Great Britain, there were 415 deaths from asbestos-related diseases from plumbers, heating and ventilating engineers in 2021. The risk of asbestos exposure is significant within the plumbing industry given the requirement to drill, join, grind, cut and repair plumbing materials, as well as handle, remove and replace parts such as pipes, pumps, gaskets and valves. Plumbers have also been known to handle asbestos cloth, which is placed behind pipe joints to heat them up prior to soldering.
All of these activities increase the chance of damaging/disturbing the asbestos and releasing fibres into the air, increasing the risk of mesothelioma and similar asbestos-related illnesses. Friable asbestos is particularly dangerous, given that the fine asbestos fibres are even more likely to be released into the air and inhaled.
What legislation is in place to protect my workforce against the risks of asbestos in plumbing?
The Control of Asbestos Regulations (2012) identify who is responsible for managing asbestos and sets out the steps that duty holders must carry out to reduce the level of risk. In line with Regulation 10 of CAR 2012, organisations must ensure that anyone who may be liable to disturbing asbestos during their work receives the correct level of information and training to carry out the plumbing work safely and competently.
Plumbers must be properly trained in asbestos awareness and must know how to report findings prior to undertaking work around asbestos. Employers/duty holders should ensure that plumbers are well informed as to where ACM/s are located on the premises so that they do not accidentally disturb or remove it. Finally, Regulation 5 of CAR 2012 states that employers must not undertake work which exposes/is liable to expose employees to asbestos in any premises.
In addition, the Health and Safety at Work Act 1974 places a duty on every employer to ensure the health, safety and welfare at work for all employees and non-employees who may be affected by the employer’s activities. The Management of Health and Safety at Work Regulations 1992 further expands upon these duties by requiring employers to assess health and safety risks to their workforce.
How can SOCOTEC support with the safe management of asbestos in plumbing?
SOCOTEC’s Asbestos team can support your workforce with Asbestos Awareness training and support with aspects of your organisation’s ‘duty to manage’, such as asbestos management surveys.
Want to find out how SOCOTEC’s Asbestos team can support your plumbing organisation? Click here.
Manufacturing & Engineering Magazine | The Home of Manufacturing Industry News
Manufacturing & Engineering Magazine, abbreviated to MEM, is a leading UK engineering magazine and manufacturing news source, covering a wide assortment of industry news sectors such as: contract manufacturing, 3D printing, structural and civil engineering, automotive manufacturing, aerospace engineering, marine engineering, rail engineering, industrial engineering, CAD and schematic designs.
Head Office +44 (0)1484 437314 production@memuk.org
Editorial / News editorial@memuk.org