Posted in

What is melt temperature in injection molding?

Hey there, let’s cut to the chase – if you’ve ever dabbled in injection molding (or spend way too much time scrolling molding forums like I do), you’ve definitely heard people rant or rave about “melt temp.” It’s not just a random number we yell at our operators when parts come out wonky – it’s actually the single biggest variable that can make or break a mold run. I’m the guy who runs the injection molding machine supplier side of things, so I’ve seen first-hand what happens when someone underestimates this, overcooks it, or just plain guesses at it. Let’s break this down like we’re hanging out at the shop floor, not in a stuffy engineering lecture hall. Injection Molding Machine

First off, let’s define it simply, no jargon junk. Melt temperature in injection molding is the actual temperature of the plastic resin right before it gets injected into the mold cavity – not the temp the machine’s control panel says it’s set to. Wait, hold up, that’s a key point. The barrel zones on your injection molding machine have a set temp, but the resin doesn’t heat evenly as it travels from the hopper down to the nozzle. The control panel reading is a guide, not the real-deal melt temp. I’ve had a new shop owner come to me complaining their control said the zone was at 450°F but their parts were burning, and when we stuck a melt probe in the nozzle, it was actually 520°F. The machine’s thermocouple was old and reading low – that’s how easy it is to get this wrong.

Why does this matter so much? Let’s think about what plastic is doing in the barrel. Most resin starts as pellets – solid, cold, hard little bits. As they move through the barrel, friction from the rotating screw actually generates heat too, not just the heaters on the barrel. That’s why even if you set a zone lower, the screw’s rotation can add extra degrees. So melt temp is a mix of barrel heater settings, screw speed, back pressure, and how fast you’re feeding resin. If it’s too low, the plastic is still a solid paste, not fully melted. That means it won’t flow into the tiny details of the mold – like the text on a toy or a thin wall on a medical part. You get short shots, cold slugs, parts that look like they’re cracked before they even cool. I once watched a customer run a polycarbonate part with melt temp 50°F too low, and every tenth part was a scrap because the flash was tiny un-melted pellets stuck on the edges. Total waste, and they didn’t even notice until we checked.

Now, too high of a melt temp? That’s just as bad, maybe worse. Different plastics have a “degradation temp” – the point where the long polymer chains start breaking down. For something like ABS, that’s around 500°F; for polypropylene, it’s a bit higher, but not by much. If you go over that, you get discolored parts, bubbles, brittleness, or even gas that builds up in the mold and causes sink marks. I had a customer running a nylon part cranked up to 600°F because they thought “hotter flows better” – by the end of the day, every part was yellow, and the nozzle was gummed up with degraded resin. They had to take the whole machine apart to clean it, which cost them way more than if they’d just nailed the temp to 530°F like the resin spec sheet said.

Wait, let’s talk about that spec sheet. Every resin has a recommended melt temp range, right? It’s not a single number, it’s a window. For example, LDPE is usually 300-450°F, HDPE is 350-500°F, PET is 480-580°F. But that’s just a starting point. Why? Because your machine, your mold, your part design all tweak that. If you’re running a part with super thin walls, you might want to be closer to the higher end of the range so the plastic flows better before it cools. If you’re running a thick, heavy part, you might stay lower to avoid degradation. Also, the type of injection molding machine you use matters – hydraulic vs electric, screw design even changes things. I always tell new customers: use the spec sheet range as your base, then test 10°F above and below to find your sweet spot. No need to go all the way to the edge unless you have to.

Let’s get into how we actually measure melt temp, because that’s where a lot of mistakes happen. Like I mentioned earlier, the control panel’s zone temp isn’t the real melt temp. The best way is a melt temperature probe – you stick it into the nozzle right before injection, that’s the actual temp of the resin that’s going into the mold. Some people use infrared guns, but that only reads the surface, not the inside of the melt. Infrared is good for checking the mold surface, not the plastic melt. I’ve seen guys waste hours with an IR gun thinking they nailed the temp, only to find the real melt temp is 40°F off. Don’t be that guy. If you’re serious about consistent parts, invest in a basic melt probe for your injection molding machine. It’s way cheaper than the scrap parts you’ll avoid.

Another big factor people miss: back pressure. Back pressure is the amount of resistance the screw has when it’s retracting to build up melt. Higher back pressure means more friction, so more heat generated, which raises melt temp. A lot of operators crank back pressure up to get a more uniform melt, which works, but if you don’t account for that, your melt temp will be higher than your control panel says. I had an operator at a small shop forget he cranked back pressure up to 150 psi, and when he dropped it to 50 psi, his melt temp went down 30°F overnight, and his short shots went away. It’s the little stuff, right?

Let’s talk about common myths, because I hear these all the time. Myth #1: “Higher melt temp makes parts stronger.” No, not always. Degraded plastic has weaker chains, so parts made with overheated plastic are actually more brittle, not stronger. I’ve tested this – overheated ABS parts broke at half the load of parts run at the correct temp. Myth #2: “Melt temp only matters for complex parts.” Wrong, even simple sprues and runners can get messed up. If your sprue is too cold, it’ll break off and get stuck in the nozzle, or leave a rough spot on the part. Myth #3: “The machine will fix it.” No, injection molding machines are tools – they follow your settings. If your settings are wrong, the parts will be wrong. I see this all the time: guys blame the machine for bad parts when it’s just their melt temp.

Wait, let’s tie this to what I do as an injection molding machine supplier. A lot of customers come to me because their existing parts are inconsistent, and when we dig in, melt temp is the culprit. The old machine they bought 10 years ago has a worn barrel, so it can’t heat evenly, or the thermocouples are bad, so the temp reading is off. Or they’re not using a melt probe, so they’re guessing. That’s why when we sell a machine, I don’t just hand over the manual – I sit with the operator for a shift to show them how to check real melt temp, adjust settings, and read the signs of wrong melt temp. Like, if the part has silver streaks, that’s usually too much moisture (but sometimes too hot), if it has flow lines, that’s often too low melt temp. I teach them to spot those signs before they make a whole batch of scrap.

Let’s give a real example. Last month, a customer was running a 5-gallon bucket out of HDPE. They were getting sink marks on the bottom, and parts were warping. Their current melt temp was set to 400°F, which was in the spec range, but when we checked with a probe, it was actually 430°F because their screw speed was too high. We dropped the screw speed by 10 RPM, so less friction heat, and their melt temp dropped to 395°F – right in the middle of the spec range. The sink marks were gone, warping was down, and they cut their scrap rate by 12%. All from tweaking melt temp, no new mold, no new machine. That’s the power of getting this right.

Another example: medical parts. These have super strict specs, so melt temp is non-negotiable. If you’re running a syringe barrel out of polypropylene, too high melt temp will break down the resin, leaving micro-particles that can’t be in medical parts. Too low, and the barrel won’t form the thin, precise wall, so it leaks. I work with a few medical molding shops, and they have a melt probe permanently mounted on their injection molding machine nozzle – they check it every hour. No guessing, no scrap, they hit their QA numbers every time.

So, how do you nail melt temp for your process? Let’s make a quick, actionable list, no fancy steps: 1. Grab the resin spec sheet – write down its recommended melt temp range. 2. Ditch the control panel’s temp as the only source – use a melt probe to check actual temp at the nozzle. 3. Test 10°F above and below your starting temp, note what happens to part quality, cycle time, scrap. 4. Adjust screw speed and back pressure if your melt temp is off from your desired set – remember, friction adds heat. 5. Check your thermocouples on your injection molding machine every few months – old ones give bad readings. If you’re running a worn machine, maybe a tune-up or new barrel will help, but 90% of the time, it’s just checking the real melt temp.

Wait, I should also mention different types of molding, like structural foam or micro molding. For micro molding, melt temp is way more critical – you’re injecting parts that are tiny, like 1mm thick, so the melt has to be exactly the right temp to flow into the mold without cooling too fast. For structural foam, you might run a bit lower melt temp because you need the gas bubbles to form properly, so overheating would break down the foam structure. That’s why I always ask customers what kind of parts they run, how thick they are, before I suggest settings – one size doesn’t fit all.

Here’s the thing I tell every new customer when they pick out an injection molding machine from me: a machine is only as good as the settings you put into it. Melt temp is the foundation of those settings. If you get that right, everything else – pressure, cycle time, cooling – works easier. If you get that wrong, you’ll spend more time fixing bad parts than making good ones. I’ve seen shops go from 20% scrap to 2% just by mastering melt temp. That’s the kind of win everyone wants, right?

Now, if you’re reading this and thinking, “Ugh, my shop is dealing with short shots, scrap, inconsistent parts because of melt temp” – I get it. This stuff is overwhelming, especially when you’re already juggling 10 things at once. I’m here to help. Whether you need to learn how to check your real melt temp, upgrade your injection molding machine to get more consistent heating, or just troubleshoot why your parts are off, we can talk. No sales pitch junk, just real advice from someone who’s been in the shop with you, fixing the same problems. If you’re tired of guessing at melt temp and want to get your parts right, hit us up for a no-pressure chat about your specific process. We can even walk you through a quick test to find your ideal melt temp, no strings attached.

Plastic Injection Machine References

  1. Rosato, D. V., & Rosato, M. G. (2000). Injection Molding Handbook (3rd ed.). Kluwer Academic Publishers.
  2. Giles, H. F., Wagner, J. R., & Mount, E. M. (2004). Extrusion: The Definitive Processing Guide and Handbook. William Andrew Publishing.
  3. International Organization for Standardization. (2018). ISO 294-1: Plastics – Injection Molding of Test Specimens of Thermoplastic Materials – Part 1: General Principles.

Ningbo Lisong Injection Molding Technology Co., Ltd.
As one of the most professional injection molding machine manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to buy advanced injection molding machine for sale here from our factory. Welcome to contact us for customized service and ODM service.
Address: No.16, Qiancai Road, Sanqishi,Yuyao City, Zhejiang, China.
E-mail: lisong@chinalisong.com
WebSite: https://www.in-jectionmachine.com/